Facebook
Like our Facebook page and
follow us on Instagram for access
to specials and discount codes!
Instagram






  Store > 2.5T Rockwell >

Rockwell 2.5 Ton RCV Ultimate 4340 Chromoly Axles | 16 Spline
RCV Axle Shafts
Photo is for illustration purposes only and may
not be an accurate depiction of this product.
  

Status: Currently Unavailable
Product Code: RCV-CVJRCK-16

Description Compatibility Part Numbers
 

Model: Vehicle / Application:
CVJRCK-16 2.5 Ton Rockwell Steering Axle - 16 Spline

These RCV Axles fit 2.5 Ton Rockwell steering axles with 16 spline axle shafts.


 Inner Splines: 16
Outer Splines: 16 		Left Inner Length: 25.602"
Right Inner Length: 32.972"
Outer Stub Length: 12.25" 		Warranty: Up to 47" Tires
Axle Seal: No Boot Needed

*Shaft lengths are OEM shafts measured from center of U-joint to end of splined shaft.*


RCV Ultimate CV Axles replace your stock u-joints with ultra high-strength constant velocity joints and 4340 chromoly shafts that are twice as strong as OEM axles. They are rated for oversize tires, high horsepower engines, and aggressive driving which are all covered under RCV's unprecedented limited lifetime warranty. Axle sets includes right and left side CV axle shafts, SST seals and installation tool (for exposed knuckle axles), installation instructions, synthetic moly grease, and installation hardware. Black oxide coating is standard with nickel plating available for extra corrosion at an additional cost. RCV axles are highly recommended by Filthy Motorsports and almost all of our Ultra4 racers, desert racers, and rock bouncers run them.


Maximum Strength At All Angles
RCV axle shafts feature 4340 chromoly housings, bearings cages, inner races and axles shafts that have proven in tests to be twice as strong as OEM axle shafts. Even more impressive is that they maintain their strength all the way up to 45 degrees where normal axles would be at their weakest point.

RCV Axle Shafts
To learn more about U-Joints and CV shafts, see U-Joint Sizes and Strength Comparisons


Constant Output Shaft Speed
The weak link in u-joints axle shafts is that they bind when the angle between the input and output shafts increases which causes the speed of the output shaft to change multiple times during every rotation. This weakness is further exaggerated when you add large tires and more power. RCV has solved these problems with a Rzeppa style CV joint that spreads the torque load over six bearings in a housing that keeps both input and output shafts at equal angles for constant shaft speeds up to an astonishing 45 degrees.

RCV Axle Shafts
To learn more about U-Joints and CV shafts, see U-Joint Sizes and Strength Comparisons


Built To Perform, Built to Last
RCV Ultimate CV Axles are engineered to be that last axle shafts you will ever need. In addition to their constant velocity design that spreads torque over 6 internal bearings, RCV axles feature chromoly shafts, housings, bearing cages and inner races. They are fully black zinc coated to prevent corrosion and the internals are REM polished for decreased wear and smoother movement. An external Zerk fitting makes for easy lubrication and the design itself requires less frequent maintenance.

RCV Axle Shafts


Limited Lifetime Warranty - No Questions Asked
RCV is so confident in the quality and reliability of their Ultimate CV Axles that they back them all with a “No Questions Asked” lifetime warranty. If you break it, they will replace it!

RCV Axle Shaft images are ©Copyright RCV Performance, used with permission.
Additional images and product descriptions are © Copyright Filthy Motorsports, LLC.
Features
  • No Questions Asked Limited Lifetime Warranty
  • 4340 Chromoly Shafts and Components
  • External Zerk Fitting for Easy Lubrication
  • Up to 45 Degree Steering Angle
  • REM Polished Internals for Reduced Wear
  • Black Oxide Coating for Corrosion Resistance
  • Rebuild Kits Available
  • Made in USA


Share your knowledge of this product with other customers... Be the first to write a review